Industrial engineering supplies · Harare, Zimbabwe
+263 780 864 277|sales@beccentric.net

TECHNICAL RESOURCES · BECCENTRIC

Specify the circuit.
Match the component.

A practical checklist for replacement parts and new pneumatic requirements. Use the complete reference and operating conditions to prepare your enquiry.

Pneumatic tubing & hose

Push-in fittings are normally selected by tube outside diameter. State OD and ID separately, plus the material, required length and colour. Pressure capability changes with material, diameter and temperature: a tubing rating does not raise the rating of a connected fitting. Include moving-machine duty and cleaning exposure.

  • Tube OD × ID, material and complete reference
  • Length, coil / cut-length requirement and colour
  • Air pressure, temperature, bend radius and fitting compatibility
Browse pneumatic tubing & hose ↗

Fittings & speed controls

Tube size and thread size describe different connections. Identify R, Rc, G or NPT threads and whether the second end accepts tube or a threaded component. Speed controllers also need meter-in or meter-out operation and the installation direction. Do not assume that changing thread sealant makes different thread forms compatible.

  • Tube OD and material; thread standard and size
  • Straight / elbow / tee / reducer arrangement
  • Flow direction, speed-control function and working conditions
Browse fittings & speed controls ↗

Cylinders & actuators

Send the complete cylinder code and measured mounting dimensions. Bore sets theoretical force for a given pressure, but friction, load direction, speed and pressure losses affect the usable result. A compact cylinder and an ISO profile cylinder with the same bore are not dimensional substitutes. Guided types support defined loads and moments; check the selected model rather than loading an ordinary piston rod sideways.

  • Bore × stroke, action, rod thread and mounting
  • Load, travel speed, cushioning and available air pressure
  • Sensor requirement, environment and replacement photographs
Browse cylinders & actuators ↗

Directional valves & manifolds

Match the circuit symbol as well as the reference. A 5/2 valve operates differently from a 5/3 valve, whose centre condition must also be specified. Coil voltage, connector, manifold footprint and pilot supply all matter. Supply pressure affects pilot operation; normal state and loss-of-power behaviour must be confirmed from the actual circuit.

  • Circuit function and centre condition / normal state
  • Ports, flow requirement, manifold and pilot arrangement
  • Coil voltage, connector, wiring and complete suffixes
Browse directional valves & manifolds ↗

Air preparation & regulation

Choose filtration, regulator range and flow capacity from the equipment and air-quality requirements. Include inlet pressure, downstream setpoint, flow, port size and drain type. A lubricator is only appropriate where the connected equipment calls for lubrication. General pneumatic filters do not establish food-contact or breathing-air quality.

  • Inlet pressure, regulated setpoint and required flow
  • Filtration stage, bowl / guard and drain arrangement
  • Port standard, installation environment and air-quality target
Browse air preparation & regulation ↗

Sensors & pressure switches

Cylinder switches depend on the actuator magnet, slot or mounting bracket. Match PNP / NPN, normally open / closed, voltage, connector and pinout. Magnetic cylinder sensors and inductive metal-detection sensors are different devices. Pressure switches need the measuring range and switching function, not just the air-line pressure.

  • Actuator / sensor model, mounting slot or bracket
  • Output, supply voltage, connector and pinout
  • Pressure range / switchpoint or target and sensing gap
Browse sensors & pressure switches ↗

Vacuum generation & handling

Vacuum holding depends on the workpiece surface, cup geometry, orientation, acceleration and leakage. Include object mass, porosity, temperature and cycle time. Cup material must suit the object and cleaning conditions. An ejector must be sized for evacuation time and leakage with the actual supply pressure; a vacuum indication alone is not proof of safe holding.

  • Workpiece weight, dimensions, surface and orientation
  • Cup size / shape / material and required lift motion
  • Air supply, vacuum / suction-flow needs and cycle time
Browse vacuum generation & handling ↗

Keep food-process requirements explicit.

Tell us if air or components contact the product, and specify cleaning chemicals, temperature and washdown exposure. Request suitable materials and declarations for the selected item. Component colour, stainless construction or a standard filter alone does not establish hygienic suitability.

This guide supports component enquiries. Final sizing, installation, machine safety and operating limits must be checked for the exact selected assembly.

LET’S GET YOUR ENQUIRY MOVING

Have a part number, a photo
or a maintenance list?

Let’s talk